VietnamSwivel connector pipe fitting male female insert HVAC brass fitting 1 4 - 4 for water oil gas plumbingReasonable design

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Pipe Fittings & Steel Nipples - pipe-valve-fitting.com

    Also known as ball-seat hose nipples, these fittings consist of a barbed shaft with a rounded end that sits inside a female threaded nut. When mated with a male threaded fitting, the rounded end presses tightly against the inside of the male threads for a better seal than a single-piece fitting. Once assembled, insert the …

    Get Price
  • Link to Master Table of Contents Brass Fittings Link to ...

    2015-11-23 · Male Connector page G22 149F-X-MIX Male Elbow page G22 159F-X-MIX 45° Male Elbow page G22 50GHSV Swivel Connector page G19 222P-X-MIX Adapter page G22 68HB-X-MIX Male Connector page G20 169HB-X-MIX Male Elbow page G22 179HB-X-MIX 45° Male Elbow page G22 69GH, 70GH, 71GH Male Pipe page G19 75GH Connector page G19 78GH, 79GH, 80GH, 81GH Male …

    Get Price
  • Tube Fittings and Adapters | Fittings | Swagelok

    An advanced-geometry, hinging-colleting back ferrule design is standard on all 1/4 to 1 in. and 6 to 25 mm Swagelok stainless steel tube fittings to help installers make more consistent, leak-tight tube connections.

    Get Price
  • Gas Piping Fittings - Plumbing & HVAC Distributor

    1/2' x 48' Yellow Coated Stainless Gas Connector, 30C Series. Watts. Product: D0548GCC. Product Type : Pipe & Fittings. Qty : Add to cart.

    Get Price
  • FITTINGS - HVAC Heating and Plumbing Supplies

    FITTINGS - HVAC, Kitchen, Bathroom, Heating and Plumbing Supplies, Shop RJ Supply House for the cheapest prices and best quality. ... 1/2″ x 1/2″ Brass PEX x Female Drop Ear 90° Elbow, Lead Free 13.39 Your Price: 9.75. ... PLUMBITE 3/4 X 1/2 REDUCING CPLG (LEAD FREE) BAGGED. 1/2″ x 1/2″ FPT (Bagged) PlumBite …

    Get Price
  • Copper & Brass Pipe & Fittings - Desco

    1/2' C x C Copper Wrot Pressure 90 Degree Elbow. Multiple Manufacturers. Product: 90C12. Product Type : 90 Degree Elbows. Material : Copper. Qty :

    Get Price
  • Air Conditioning Fittings, Hoses & Spares | Repco

    Burgaflex Steel Fitting #08-08 90° With H-R134a Port Female O-Ring (FOR) - Reduced Burgaclip - SCX1322-3 Bazaarvoice SAP …

    Get Price
  • Other Fittings & Adapters for sale | eBay

    2pcs 1/4' Hose Barb Tee Brass Pipe 3 Way T Fitting Thread Gas Fuel Water Air. 4.5 out of 5 stars (18) Total Ratings 18, ... 5405-06-06 Hydraulic Fitting 3/8' Male Pipe to 3/8' Female Pipe. 7.00 ... 2pcs 1/4' Hose Barb Tee Brass Pipe 3 Way T Fitting Thread Gas Fuel Water Air. 4.5 out of 5 stars (18) Total Ratings 18, 87% agree ...

    Get Price
  • Video: How To Install Push To Connect Fittings |

    2021-8-5 · 2. Cut pipe cleanly & squarely. Be sure the pipe is free of scratches or debris and cut the pipe as cleanly and squarely as possible. If you are working with copper pipe, use a deburr tool or sand paper to remove any sharp edges or burrs on the pipe. Failing to deburr the pipe properly can compromise the fitting. 3. …

    Get Price
  • How to Measure Pipe and Fitting Sizes | Zoro.com

    For Male Threads. 1. Measure the Outside Diameter (OD) of your pipe or pipe fitting: Wrap a string around the pipe. Mark the point where the string touches together. Use a ruler or measuring tape to find the length between the tip of the string and the mark you made (circumference) Divide the circumference by 3.14159. 2.

    Get Price
  • Measuring Pipes and Pipe Fittings

    2017-7-13 · The OD of pipe fitting must be measured & compared to the table for identification For example, a 3/4' NPT pipe thread has an outside diameter of 1.050 inches and 14 threads per inch. Each thread size has a defined number of threads per inch (TPI), but several sizes have the same TPI; because of this, both the TPI and …

    Get Price
  • How To Install Sharkbite Fittings On A Copper

    Push the pipe. Using a slight twisting motion, push the pipe firmly into the SharkBite fitting until you hit the tube stop. Ensure proper placement. To make sure that the pipe has been properly inserted, verify that the depth mark you made is within 0.005 inches of the end of the release collar.

    Get Price